Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
EMStudio not happy
#1
I have
http://builds.libreems.org/Firmware/0.2....-4of69.s19
loaded in Jaguar which is ported to my simulator and things are not going well. At one time I was able to read some real time data, ADC outputs in particular. There were problems with the trigger signal, which was not altogether surprising, but now I don't even get the real time data.

Is there a trouble shooting procedure I can use to try determine what the problem is?
Robert
1995 Ford E-150, 300 CID I6, E4OD, custom MS1-Extra
1992 Winnebago Elante 33 RQ, Ford 460 CID V8, E4OD, custom MS1-Extra
1993 Bayliner 3288, twin Ford 351 CID Windsor V8s, converted to programmable EFI, custom MS1-extra
Reply
#2
EMStudio creates application logs in /home/username/EMStudio/applogs

When you say it is not getting real time data, is it interrogation properly without any errors? What does the "PPS" in the lower left hand corner say?
Reply
#3
(01-29-2014, 02:14 PM)malcom2073 Wrote: EMStudio creates application logs in /home/username/EMStudio/applogs

When you say it is not getting real time data, is it interrogation properly without any errors? What does the "PPS" in the lower left hand corner say?

PPS changes between 81, 82 and 83. It also says No file loaded
Robert
1995 Ford E-150, 300 CID I6, E4OD, custom MS1-Extra
1992 Winnebago Elante 33 RQ, Ford 460 CID V8, E4OD, custom MS1-Extra
1993 Bayliner 3288, twin Ford 351 CID Windsor V8s, converted to programmable EFI, custom MS1-extra
Reply
#4
(01-29-2014, 06:36 PM)E4ODnut Wrote:
(01-29-2014, 02:14 PM)malcom2073 Wrote: EMStudio creates application logs in /home/username/EMStudio/applogs

When you say it is not getting real time data, is it interrogation properly without any errors? What does the "PPS" in the lower left hand corner say?

PPS changes between 81, 82 and 83. It also says No file loaded



That means you're getting real time data, what makes you think you aren't?

(01-29-2014, 06:36 PM)E4ODnut Wrote:
(01-29-2014, 02:14 PM)malcom2073 Wrote: EMStudio creates application logs in /home/username/EMStudio/applogs

When you say it is not getting real time data, is it interrogation properly without any errors? What does the "PPS" in the lower left hand corner say?

PPS changes between 81, 82 and 83. It also says No file loaded

That means you're getting real time data, what makes you think you aren't?
Reply
#5
My simulator has pots for TPS, EGO, Coolant Temp and Manifold air temp ported to the appropriate pins on Jaguar. I also have a vacuum pump to test MAP and Barometric pressure. These values remain constant and "out of range" no matter what position I have the pots turned to.
Robert
1995 Ford E-150, 300 CID I6, E4OD, custom MS1-Extra
1992 Winnebago Elante 33 RQ, Ford 460 CID V8, E4OD, custom MS1-Extra
1993 Bayliner 3288, twin Ford 351 CID Windsor V8s, converted to programmable EFI, custom MS1-extra
Reply
#6
I would check the millisecond clock variable to see if live data is coming across. It's sounding more and more like your ADC's are either fried, or something is equally wrong with them.
Reply
#7
Yep, all three clocks are working. Not looking good for the ADCs.
Robert
1995 Ford E-150, 300 CID I6, E4OD, custom MS1-Extra
1992 Winnebago Elante 33 RQ, Ford 460 CID V8, E4OD, custom MS1-Extra
1993 Bayliner 3288, twin Ford 351 CID Windsor V8s, converted to programmable EFI, custom MS1-extra
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)